Airplex Soft Roll-Up Tonneau Cover — Ford F-150
A lightweight vinyl roll-up cover built specifically for the Ford F-150’s 5.5 ft bed. The marine-grade top rolls back in seconds for full bed access, and mounts with bed rail clamps — no drilling required.
Shop This CoverOverview
This roll-up cover is built specifically for the Ford F-150’s 5.5 ft bed, not trimmed down from a universal size. A low-profile aluminum frame mounts to the bed rails, and a marine-grade vinyl top stretches over it, held taut by a tensioning system built into the frame rails so the top doesn’t sag or flap at highway speed.
Because the top rolls back on itself rather than folding into panels, this is the fastest way to get full, unobstructed bed access on an F-150 — release the side latches, roll the vinyl toward the cab, and the entire bed is open. It’s also the lightest cover in the Airplex lineup, which matters if you ever want to remove it completely for a long haul.
Built From
Vinyl Top
Marine-grade, UV-treated vinyl resists fading, cracking, and mildew even with regular outdoor exposure.
Seals
EPDM rubber rail and tailgate seals stay flexible through repeated hot and cold cycles, keeping rain and dust out.
Frame
A low-profile aluminum rail frame supports the vinyl top and keeps it tensioned so it doesn’t sag between the rails.
Latch System
A tailgate and side latch strap system keeps the rolled or closed top secure at highway speed.
Confirming Your Ford F-150’s Fit
Bed length has to match exactly for the frame to tension correctly and the seals to sit right. This cover is built for the F-150’s 5.5 ft bed — check your bed length on the door jamb sticker or in your owner’s manual before ordering, since the F-150 is also sold with 6.5 ft and 8 ft bed options depending on cab configuration.
How Installation Works
- Clean the bed rails. Wipe down the factory rail where the frame clamps will sit.
- Assemble the frame. Snap or bolt the low-profile side rails together per the included instructions.
- Clamp the frame to the bed rails. Hand-tighten the included clamps, then torque them down evenly.
- Attach the vinyl top. Snap the top onto the frame and adjust the tensioning system so it sits flat with no sag.
- Test the latches. Roll the top open and closed, checking that the side latches engage cleanly.
Specifications
Why This Cover
- Marine-grade, UV-treated vinyl resists fading and cracking outdoors
- Rolls back toward the cab in seconds for full bed access
- Rail clamp mounting means no drilling into the Ford F-150’s bed
- Lightest cover style in the Airplex lineup
- Clears factory tailgate hardware, steps, and hitch-mounted accessories
Frequently Asked Questions
Does this fit the 2015–2024 Ford F-150?
Yes, this cover is fitted for Ford F-150 model years 2015–2024 with a 5.5 ft bed. Check your bed length on the door jamb sticker if you’re unsure which bed size your truck has.
How do I roll the cover up for full bed access?
Release the side latch straps, then roll the vinyl top toward the cab and secure it with the included tie-down straps — takes about 10 seconds once you’ve done it a couple times.
Can I install this by myself?
Yes. It ships as a rolled vinyl top with a separate low-profile frame kit, and mounts with included rail clamps — most owners complete the install solo in under an hour.
Will the vinyl top sag or flap on the highway?
No, as long as the frame’s tensioning system is adjusted correctly during install. A properly tensioned top sits flat and doesn’t flap even at highway speed.
How do I clean and maintain the vinyl top?
Wipe it down with mild soap and water — avoid harsh solvents, which can dry out the vinyl over time. Replacement seals and latch straps are sold separately if either ever wears out.
Ready to Cover Your Ford F-150 Bed?
Rail-clamp mount, no drilling, load-rated top — fitted to your exact truck.
Shop This Cover